Easy-to-follow Guide to Installing a New Shower Unit

Contact Us Now

Are you interested in advice on How to Install a Freestand?

A successful shower installation calls for careful planning and also a lot of job. For the most part, you will need to do 3 kinds of jobs: framing wall surfaces, setting up the plumbing, and also finishing wall surfaces.

Prep work

First of all, you have to decide on the kind of shower that you desire to install. It is very important to ascertain whether the chosen shower is capable of dealing with certain systems and also can manage a safe level of water with the central heating boiler. A lot of shower devices nowadays are developed to be adaptable to various water pressures (such as stored hot water as well as chilly keys).
It is additionally vital to take into consideration the water stress as well as the preparation of the piping as well as drainage for the shower

Different Types of Shower Units

Push-on Mixer: The tube and also spray parts of the push-on mixer shower unit can be connected to the bath faucet according to your demand, and the water temperature can be readjusted by means of the taps. Push-on mixers are cheap and also very easy to install. Nonetheless, although the pipe connection is straightforward, it is quickly dislodged. Furthermore, it is bothersome to adjust the temperature level.

Bath/Shower Mixer: The hose pipe and also spray of this kind of shower are incorporated with a bath mixer faucet, and also the temperature can be adjusted with the bathroom taps. It is an extremely low-cost alternative and no additional plumbing is entailed. However, the bath/shower mixers also suffer from bothersome temperature control alternatives.

Handbook Mixer: The hose and also spray of a hand-operated mixer shower unit belong of the wall unit and the cold and hot water supplies are attached to a single shutoff The temperature as well as stress of the water are controlled with either one or a variety of knobs (in extra expensive showers). Although temperature control is much easier in manual mixer types, they are more expensive than the formerly stated mixers. They additionally need additional plumbing of cold and hot water supply pipelines.

Thermostatic Mixer: The tube as well as spray of this shower kind belong of the wall system and the hot and cold water products are connected to a solitary valve here too. It is total with an integrated stabiliser to self-adjust the water temperature and to stop it from becoming as well warm. One of the biggest advantages of a thermostatic mixer shower kind consists of practical temperature level control. However, it is the most costly of the different mixer choices.

Power Shower: A power shower is a single system consisting of a powerful electrical pump that can altering both the water pressure and temperature level. This sort of shower can be fitted if there is supply of water from a cold water tank and also a hot water cylinder. A power shower makes the modification of both pressure and temperature easy. On the other hand, it is unsuitable for water warmed straight by the shower or where the water is provided by a combination boiler under keys pressure.

Electric Shower: An electric shower is plumbed right into a keys cold water supply as well as it heats the water electrically. It is essential to note that for this shower kind to be set up, the mains pressure requires to be at least 0.7 kg/sq centimeters (10lb/sq in). The system allows the temperature level and stress to be changed using a handle. Designs with temperature stabilisers are much better as they continue to be untouched by other faucets somewhere else in use within the family. A major disadvantage of electrical showers is that the control knob just enables the alternative of high temperatures at much less pressure, or reduced temperatures at a better pressure. This is problematic in the winter season when the spray is typically weak and also the mains water is chillier. Nonetheless, this problem is taken on in some models which are offered with a winter/summer setup.

Technique

Depending on the sort of shower you desire to mount, the shower head need to either be fitted in order to prevent its contact with the water in the bathroom listed below or the base tray, or it has to have a check shutoff.
Prior to beginning, it is advisable to note the placements of the shower head as well as control, and to plan the pipe-work entailed. In addition, the drain system to remove the drainage will certainly need to be planned. Both placements of the cable television route and also the shower switch will likewise need to be taken into consideration if an immediate or electric shower device is being set up.
Use the direction guide supplied with the shower unit to fit the shower control.Before fitting the pipelines that will supply the water to the shower system, it is necessary to cut off the water system. In order to safeguard the pipelines, they should be provided a water-proof covering and also fitted with separating valves. The pipelines can then be hidden right into the wall as well as plastered over to neaten the general appearance.
Fit the base tray, shower head, as well as installations.
Connect the primary shower control to the pipelines that will be providing the water (This may need a women screw thread adapter).
Reconnect the water system and also test the pipes for any type of leakages, as some might need tightening.
If you are mounting an electric shower, remember to switch off the power supply prior to making any kind of electric connections. Once these links have been made (there ought to be guidance within the user's manual), the power supply can be changed back on.

Adjusting Water Stress to Fit Your Shower

The cold water reservoir can be raised to a better height (in some cases just 150mm (6inches)) by fitting a solid wooden assistance below it - perhaps composed of struts and blockboards. If you select this alternative, the primary and also distribution pipes will certainly also have to be elevated to meet the new elevation of the reservoir.
Additionally, a booster pump (a solitary pump or a dual/twin pump) can be fitted. Whichever kind is chosen, it should be linked right into the power supply in order to run.

Piping and also Drainage

It is best to utilize 15mm diameter supply pipes, and also make the runs to the shower as short and also straight as possible so regarding preserve maximum stress as well as reduce warmth loss. In addition, by reducing making use of arm joints for pipeline corners, you can lower the resistance in the circulation of the water system. You can achieve this by bending the pipes rather.

The Majority Of Common Blunders

Breaking or overlooking local code constraints.

Making use of pipes that are as well tiny.

Connecting copper to galvanized without using a brass or dielectric suitable between the two.

Not utilizing tape or pipeline compound at threaded joints.

Uneven your fixtures when mounting them.

Not installing an air void loading for fixtures.

Reducing supply stub outs as well brief to install the shutoff valves onto after the completed wall surface remains in area.

Not correctly lining up tubes right into fittings or stop valves. (Requiring the nut onto the compression ring at an angle when the tubing is at an angle will trigger a leak.).

When turning the water back on in your home, always run the outdoors pipe valve or flush your bathrooms to hemorrhage dust as well as air from the lines. This particles can trigger issues in your sink taps and also other plumbing trim.

How Do You Install a Shower? Follow This Guide

Installing a Shower at a Glance

Tools & Materials: Level, electric drill, caulk, hole saw, cedar shims, shower unit

Step 1: Drill pilot holes

Step 2: Prep fixture holes

Step 3: Move unit into place

Step 4: Caulk corners and base

Step 5: Attach door

Step 6: Install shower pan

Whenever plumbing is involved in a DIY project, people worry about what might go wrong. The truth is that installing a shower isn’t that complicated, and you can save a lot of money by doing it yourself. You shouldn’t need to make any alterations to your plumbing to complete the job, and most of the tools you need will be provided in your new shower kit.

Can I Install a Shower Myself?

Even if you’ve never installed a shower before, you’ll find this to be a project that is perfectly suited for DIYers with a moderate level of experience. Whether you're doing a bathtub conversion or installing a new stall, most of what you need comes in shower kits that you can purchase from a hardware store. The first thing you need to do is determine what type of shower stall you want.

Single-panel stalls are the easiest to install because they come preassembled. All you need to do is put them in place. Multi-panel showers require a few additional steps, but you’ve got more control over the appearance of your unit. Multi-panel units are also much easier to handle if you’re going to do the installation without any help.

Be sure to take all appropriate safety precautions, such as wearing eye protection and gloves. When you’re removing or installing a shower unit, you might kick up debris that could hurt your eyes. You’ll also need to work with equipment that will get extremely hot, so be sure to have safety gloves handy.

Tools and Materials

2- to 4-foot level

Electric drill with a 1/8-inch drill bit

Caulk

2-inch hole saw

Cedar shims

The unit itself

Before You Begin: Prep the Space

It’s highly important to measure your space accurately before putting the stall in. Measuring from the floor upward and from each corner outward will ensure you’ve got the right measurements. What you’re looking for is where the plumbing apparatuses are going to come through the stall. Transfer these measurements over to the back of your unit by drawing the locations of these holes using a pencil or marker.

Pull out your old shower and make sure to scrape off all the old caulking. Be thorough because you want to work with smooth surfaces for the best installation. Once you’ve pulled out your existing shower, you need to make sure that the floor is clean and dry. The best way to clean debris is with a shop vacuum, as it’ll soak up water and dirt together.

If you’re experiencing any plumbing issues, such as low water pressure, this is a perfect opportunity to solve them. Make sure that the pipes themselves are not in need of patching and clean your showerhead. When you turn the water back on after your project, check the pipes for signs of wear or disrepair. Anything beyond minor repairs should be handled by a plumber, and this is the best time to bring in a professional.

If the floor has any moisture at all, don’t proceed until it’s completely dry. The last thing you need is for the floor to rot or invite mold and mildew into your base. Once everything is dry, apply waterproof wallboard to the walls. This can be attached with screws or nails, then sealed with caulk so that water doesn’t seep into any crevices.

https://www.homeserve.com/en-us/blog/how-to/install-shower/

We hope you liked our piece on How to Install a Direct-to-Stud Shower Enclosure. Thanks a ton for spending some time to browse our article post. Enjoyed our blog? Please share it. Let someone else discover it. We love reading our article about How to Build a Shower Enclosure for Your DIY Bathroom.

Schedule Estimate